This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
equipment:solidoodle3 [2014/04/09 18:28] bipolarbear [Approved Trainers] |
equipment:solidoodle3 [2019/04/01 15:06] (current) raster |
||
---|---|---|---|
Line 9: | Line 9: | ||
===== Documentation ===== | ===== Documentation ===== | ||
- | * [[http://www.solidoodle.com/ | + | * [[http://support.solidoodle.com/ |
- | * [[http://www.solidoodle.com/ | + | * [[http://support.solidoodle.com/ |
+ | * [[http:// | ||
* [[http:// | * [[http:// | ||
Line 17: | Line 18: | ||
* Print Envelope: 200mm x 200mm x 200mm (8" x 8" x 8") | * Print Envelope: 200mm x 200mm x 200mm (8" x 8" x 8") | ||
* ABS Extruder Temperature: | * ABS Extruder Temperature: | ||
- | * ABS Bed Temperature: | + | * ABS Bed Temperature: |
===== Software ===== | ===== Software ===== | ||
Line 27: | Line 28: | ||
* [[http:// | * [[http:// | ||
+ | Note: There is talk of switching to Printrun. | ||
==== Slic3r ==== | ==== Slic3r ==== | ||
Line 37: | Line 39: | ||
===== Current Status ===== | ===== Current Status ===== | ||
- | * OK | + | * March 2019: Non-functional? |
+ | |||
+ | * December 2015: Having problems with over-temperature error messages when trying to print with ABS. | ||
+ | - Note: The extruder reads 25c-30c cooler than it actually is. If you want to print at 230c (for abs) you should set the hot end to 200c. | ||
+ | |||
+ | * June 2017: Out of commission for an extended period. Taken out of operation due to mechanical glitch which caused defects in every print. | ||
+ | * June 2017: E3D V6 hotend and Titan extruder transfered to TAZ for upgrades. | ||
===== Location ===== | ===== Location ===== | ||
Line 48: | Line 56: | ||
* [[members: | * [[members: | ||
* [[members: | * [[members: | ||
+ | * [[members: | ||
* Skittles (Lucy Sinogeikina) | * Skittles (Lucy Sinogeikina) | ||
- | ===== Checked Out Members ===== | ||
- | * ... | + | ===== Checked Out Members ===== |
+ | If you would like to get checked off to use this machine please contact one of the above listed trainers. | ||
+ | * Wade Starck | ||
+ | * [[members: | ||
+ | * Emily Mondloch | ||
+ | * Mykal Antczak | ||
+ | * Kaysy | ||
+ | * Steve Shapiro | ||
+ | * Sean Woodman | ||
+ | * Matt Schedler | ||
+ | * Luke Schedler | ||
+ | * Bret Daniel | ||
+ | * [[members: | ||
===== History ===== | ===== History ===== | ||
* 2014-02-25 - Arrived at Makerspace\\ | * 2014-02-25 - Arrived at Makerspace\\ | ||
Line 68: | Line 88: | ||
* $100 - Vishal R. | * $100 - Vishal R. | ||
* $20 - Harvey M. | * $20 - Harvey M. | ||
- | * $50 - Ken B. | + | * $50 |
* $200 - Jim K. | * $200 - Jim K. | ||
* $200 - Ed K. | * $200 - Ed K. |