User Tools
equipment:solidoodle3
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
equipment:solidoodle3 [2014/04/06 21:50] raster |
equipment:solidoodle3 [2019/04/01 15:06] (current) raster |
||
|---|---|---|---|
| Line 9: | Line 9: | ||
| ===== Documentation ===== | ===== Documentation ===== | ||
| - | * [[http://www.solidoodle.com/ | + | * [[http://support.solidoodle.com/ |
| - | * [[http://www.solidoodle.com/ | + | * [[http://support.solidoodle.com/ |
| - | * [[http:// | + | * [[http:// |
| + | * [[http:// | ||
| ===== Settings ===== | ===== Settings ===== | ||
| Line 17: | Line 18: | ||
| * Print Envelope: 200mm x 200mm x 200mm (8" x 8" x 8") | * Print Envelope: 200mm x 200mm x 200mm (8" x 8" x 8") | ||
| * ABS Extruder Temperature: | * ABS Extruder Temperature: | ||
| - | * ABS Bed Temperature: | + | * ABS Bed Temperature: |
| ===== Software ===== | ===== Software ===== | ||
| Line 27: | Line 28: | ||
| * [[http:// | * [[http:// | ||
| + | Note: There is talk of switching to Printrun. | ||
| ==== Slic3r ==== | ==== Slic3r ==== | ||
| Line 37: | Line 39: | ||
| ===== Current Status ===== | ===== Current Status ===== | ||
| - | * OK | + | * March 2019: Non-functional? |
| + | |||
| + | * December 2015: Having problems with over-temperature error messages when trying to print with ABS. | ||
| + | - Note: The extruder reads 25c-30c cooler than it actually is. If you want to print at 230c (for abs) you should set the hot end to 200c. | ||
| + | |||
| + | * June 2017: Out of commission for an extended period. Taken out of operation due to mechanical glitch which caused defects in every print. | ||
| + | * June 2017: E3D V6 hotend and Titan extruder transfered to TAZ for upgrades. | ||
| ===== Location ===== | ===== Location ===== | ||
| Line 45: | Line 53: | ||
| ===== Approved Trainers ===== | ===== Approved Trainers ===== | ||
| - | * Ed K. | + | * Ed C. |
| * [[members: | * [[members: | ||
| * [[members: | * [[members: | ||
| + | * [[members: | ||
| + | * Skittles (Lucy Sinogeikina) | ||
| ===== Checked Out Members ===== | ===== Checked Out Members ===== | ||
| + | If you would like to get checked off to use this machine please contact one of the above listed trainers. | ||
| - | | + | |
| + | * [[members: | ||
| + | * Emily Mondloch | ||
| + | * Mykal Antczak | ||
| + | * Kaysy | ||
| + | * Steve Shapiro | ||
| + | * Sean Woodman | ||
| + | * Matt Schedler | ||
| + | * Luke Schedler | ||
| + | * Bret Daniel | ||
| + | * [[members: | ||
| ===== History ===== | ===== History ===== | ||
| * 2014-02-25 - Arrived at Makerspace\\ | * 2014-02-25 - Arrived at Makerspace\\ | ||
| Line 68: | Line 88: | ||
| * $100 - Vishal R. | * $100 - Vishal R. | ||
| * $20 - Harvey M. | * $20 - Harvey M. | ||
| - | * $50 - Ken B. | + | * $50 |
| * $200 - Jim K. | * $200 - Jim K. | ||
| * $200 - Ed K. | * $200 - Ed K. | ||
equipment/solidoodle3.1396821055.txt.gz · Last modified: 2014/04/06 21:50 by raster
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
