User Tools
equipment:stratasysfdm2000
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
equipment:stratasysfdm2000 [2013/09/23 00:32] haveblue |
equipment:stratasysfdm2000 [2017/06/22 01:18] (current) mmelk [Current Status] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Stratasys FDM 2000 ====== | ====== Stratasys FDM 2000 ====== | ||
| + | {{: | ||
| ~~NOTOC~~ | ~~NOTOC~~ | ||
| Line 5: | Line 6: | ||
| * Stratasys FDM 2000 3D printer with ABS head | * Stratasys FDM 2000 3D printer with ABS head | ||
| * 1.75mm filament | * 1.75mm filament | ||
| - | * ABS or ABS+ plastic resin material (use _only_ Stratasys OEM filament) | + | * ABS or ABS+ plastic resin material (use _only_ Stratasys OEM filament |
| * Currently located in the 3D Printing Area | * Currently located in the 3D Printing Area | ||
| Line 12: | Line 13: | ||
| ===== Software ===== | ===== Software ===== | ||
| - | * See Have Blue for Insight 8.1 (Stratasys control software) | + | * See Have Blue for Insight 8.1 (Stratasys control software, last version to support the FDM series) |
| =====Current Status ===== | =====Current Status ===== | ||
| - | * Not working. | + | * Head has been rebuilt, support nozzle has been replaced. |
| - | * Support nozzle solenoid is broken - am seeing if it can be repaired. | + | * Spare WinXP computer for running the machine has been acquired. |
| + | * June 2017: Nonfuctional. Needs calibration and a dedicated computer setup to run it. Computer is on hand, need monitor. | ||
| =====On loan from ===== | =====On loan from ===== | ||
| * Have Blue | * Have Blue | ||
| =====History ===== | =====History ===== | ||
| - | * 2013-07-07 | + | * 7JUL2013 |
| + | * 10SEP2013 - Moved into 3D printing area and began testing\\ | ||
| + | * 1OCT2013 - Replaced support nozzle solenoid\\ | ||
| + | * 10OCT2013 - Attempted to clear support nozzle clog; cracked inlet buffer; said a lot of naughty words.\\ | ||
| + | * 17OCT2013 - replaced inlet buffer, did full cleaning of support hotend, but support side seems clogged worse than before. | ||
| + | * 22OCT2013 - Chip added a shelf to the cart for storage of filament. | ||
| + | * Late 2013/Early 2014 - disassembled head for removal of support extruder, support hotend cleaned, discovered manufacturing defect that should be easily fixed. | ||
| + | * 20APR2014 - fixed manufacturing defect in support hotend, polished internal passage, reassembled hotend with heater, thermocouple, | ||
| + | * 21APR2014 - discovered that the head rebuild didn't do squat and it was still jamming. | ||
| + | * 22APR2014 through 7MAY2014 - long, alcohol fueled depression (just kidding) | ||
| + | * 8MAY2014 - replaced support nozzle; jamming eliminated. | ||
| + | * 9MAY2014 - print completed successfully and there was much rejoicing. | ||
| =====Notes ===== | =====Notes ===== | ||
equipment/stratasysfdm2000.1379896336.txt.gz · Last modified: 2013/09/23 00:32 by haveblue
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
