User Tools
equipment:lasercutterx30
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
equipment:lasercutterx30 [2017/12/03 00:24] marcinp [Specs] |
equipment:lasercutterx30 [2023/09/13 03:30] branth |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== | + | ====== |
| - | {{ : | + | {{ : |
| + | {{: | ||
| ===== Make/Model ===== | ===== Make/Model ===== | ||
| Line 10: | Line 11: | ||
| * 19mm dia / 50.6 mm Focal Length ZnSe Lens | * 19mm dia / 50.6 mm Focal Length ZnSe Lens | ||
| * Work Area: 32" x 18" | * Work Area: 32" x 18" | ||
| + | * No air assist | ||
| * Has motorized z-axis control with auto-focus | * Has motorized z-axis control with auto-focus | ||
| * [[https:// | * [[https:// | ||
| * This accessory is almost 6" tall and reduces the workable Z-axis height, so if you need more room, temporarily remove it. | * This accessory is almost 6" tall and reduces the workable Z-axis height, so if you need more room, temporarily remove it. | ||
| + | * IP Address: 10.1.1.23 | ||
| ===== Current Status ===== | ===== Current Status ===== | ||
| Line 18: | Line 21: | ||
| * The [[wp> | * The [[wp> | ||
| * Multiple black spots on Lens | * Multiple black spots on Lens | ||
| - | * No known adverse effects | + | * No known adverse effects |
| - | * Alignment | + | * We have replacements but will wait |
| - | * Should be replaced so that we can re-align the laser if need be | + | * Some of the alignment |
| * Closing the top lid does not always align with magnetic safety switches | * Closing the top lid does not always align with magnetic safety switches | ||
| * Panel flashes < | * Panel flashes < | ||
| Line 28: | Line 31: | ||
| ===== Location ===== | ===== Location ===== | ||
| * Current: Laser Cutter Room (back wall, middle) | * Current: Laser Cutter Room (back wall, middle) | ||
| + | * Computer: Immediately to the left on the left side of the table | ||
| ===== Manual ===== | ===== Manual ===== | ||
| - | * Unknown | + | * Spiral-bound book titled " |
| + | * Even more documentation, | ||
| ===== Material Settings ===== | ===== Material Settings ===== | ||
| Line 36: | Line 41: | ||
| ===== History ===== | ===== History ===== | ||
| + | * 06/07/2008 - Replaced power supply | ||
| * 09/15/2017 - Arrived at Makerspace | * 09/15/2017 - Arrived at Makerspace | ||
| * 10/04/2017 - Inspection by Tom | * 10/04/2017 - Inspection by Tom | ||
| * 11/21/2017 - Inspection by Marcin | * 11/21/2017 - Inspection by Marcin | ||
| * 12/02/2017 - Made available for general use | * 12/02/2017 - Made available for general use | ||
| + | * 08/08/2018 - Replaced x-axis stepper motor Lin Engineering 4109V-51 3.6V 1.2A | ||
| ===== Notes ===== | ===== Notes ===== | ||
| * Do not bump the machine while it is running, the magnetic safeties are sensitive and will kill the laser if it thinks the lid is open. | * Do not bump the machine while it is running, the magnetic safeties are sensitive and will kill the laser if it thinks the lid is open. | ||
| Line 48: | Line 55: | ||
| * A full tutorial is in progress: [[spacedocumentation: | * A full tutorial is in progress: [[spacedocumentation: | ||
| * A rough tutorial on [[spacedocumentation: | * A rough tutorial on [[spacedocumentation: | ||
| + | |||
| + | {{: | ||
equipment/lasercutterx30.txt · Last modified: 2023/09/13 03:30 by branth
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
