This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
equipment:lasercutterx30 [2017/12/03 00:19] marcinp [Specs] |
equipment:lasercutterx30 [2023/09/13 03:30] branth |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== | + | ====== |
- | {{ : | + | {{ : |
+ | {{: | ||
===== Make/Model ===== | ===== Make/Model ===== | ||
Line 10: | Line 11: | ||
* 19mm dia / 50.6 mm Focal Length ZnSe Lens | * 19mm dia / 50.6 mm Focal Length ZnSe Lens | ||
* Work Area: 32" x 18" | * Work Area: 32" x 18" | ||
+ | * No air assist | ||
* Has motorized z-axis control with auto-focus | * Has motorized z-axis control with auto-focus | ||
- | * Accessory: | + | * [[https:// |
+ | * This accessory is almost 6" tall and reduces the workable Z-axis height, so if you need more room, temporarily remove it. | ||
+ | * IP Address: 10.1.1.23 | ||
===== Current Status ===== | ===== Current Status ===== | ||
Line 17: | Line 21: | ||
* The [[wp> | * The [[wp> | ||
* Multiple black spots on Lens | * Multiple black spots on Lens | ||
- | * No known adverse effects | + | * No known adverse effects |
- | * Alignment | + | * We have replacements but will wait |
- | * Should be replaced so that we can re-align the laser if need be | + | * Some of the alignment |
* Closing the top lid does not always align with magnetic safety switches | * Closing the top lid does not always align with magnetic safety switches | ||
* Panel flashes < | * Panel flashes < | ||
Line 27: | Line 31: | ||
===== Location ===== | ===== Location ===== | ||
* Current: Laser Cutter Room (back wall, middle) | * Current: Laser Cutter Room (back wall, middle) | ||
+ | * Computer: Immediately to the left on the left side of the table | ||
===== Manual ===== | ===== Manual ===== | ||
- | * Unknown | + | * Spiral-bound book titled " |
+ | * Even more documentation, | ||
===== Material Settings ===== | ===== Material Settings ===== | ||
Line 35: | Line 41: | ||
===== History ===== | ===== History ===== | ||
+ | * 06/07/2008 - Replaced power supply | ||
* 09/15/2017 - Arrived at Makerspace | * 09/15/2017 - Arrived at Makerspace | ||
* 10/04/2017 - Inspection by Tom | * 10/04/2017 - Inspection by Tom | ||
* 11/21/2017 - Inspection by Marcin | * 11/21/2017 - Inspection by Marcin | ||
* 12/02/2017 - Made available for general use | * 12/02/2017 - Made available for general use | ||
+ | * 08/08/2018 - Replaced x-axis stepper motor Lin Engineering 4109V-51 3.6V 1.2A | ||
===== Notes ===== | ===== Notes ===== | ||
* Do not bump the machine while it is running, the magnetic safeties are sensitive and will kill the laser if it thinks the lid is open. | * Do not bump the machine while it is running, the magnetic safeties are sensitive and will kill the laser if it thinks the lid is open. | ||
Line 47: | Line 55: | ||
* A full tutorial is in progress: [[spacedocumentation: | * A full tutorial is in progress: [[spacedocumentation: | ||
* A rough tutorial on [[spacedocumentation: | * A rough tutorial on [[spacedocumentation: | ||
+ | |||
+ | {{: | ||