User Tools
equipment:lasercutterx30
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
equipment:lasercutterx30 [2017/12/02 23:50] marcinp [Current Status] |
equipment:lasercutterx30 [2023/09/13 03:30] branth |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== | + | ====== |
| - | {{ : | + | {{ : |
| + | {{: | ||
| ===== Make/Model ===== | ===== Make/Model ===== | ||
| Line 8: | Line 9: | ||
| ===== Specs ===== | ===== Specs ===== | ||
| * 30 Watt CO2 Laser (dated 2012) | * 30 Watt CO2 Laser (dated 2012) | ||
| - | * //(Lens TBD)// | + | * 19mm dia / 50.6 mm Focal Length ZnSe Lens |
| * Work Area: 32" x 18" | * Work Area: 32" x 18" | ||
| + | * No air assist | ||
| * Has motorized z-axis control with auto-focus | * Has motorized z-axis control with auto-focus | ||
| + | * [[https:// | ||
| + | * This accessory is almost 6" tall and reduces the workable Z-axis height, so if you need more room, temporarily remove it. | ||
| + | * IP Address: 10.1.1.23 | ||
| ===== Current Status ===== | ===== Current Status ===== | ||
| * **ONLINE** | * **ONLINE** | ||
| + | * The [[wp> | ||
| * Multiple black spots on Lens | * Multiple black spots on Lens | ||
| - | | + | |
| - | * Closing the top lid does not always align with magnetic safety switches, you must //nudge// the lid to the right to re-align | + | * We have replacements but will wait |
| + | * Some of the alignment | ||
| + | * Closing the top lid does not always align with magnetic safety switches | ||
| + | * Panel flashes < | ||
| + | * You must //nudge// the lid to the right to re-align | ||
| + | * Panel flashes < | ||
| ===== Location ===== | ===== Location ===== | ||
| * Current: Laser Cutter Room (back wall, middle) | * Current: Laser Cutter Room (back wall, middle) | ||
| + | * Computer: Immediately to the left on the left side of the table | ||
| ===== Manual ===== | ===== Manual ===== | ||
| - | * Unknown | + | * Spiral-bound book titled " |
| + | * Even more documentation, | ||
| ===== Material Settings ===== | ===== Material Settings ===== | ||
| Line 28: | Line 41: | ||
| ===== History ===== | ===== History ===== | ||
| - | * 09/15/2017 Arrived at Makerspace | + | * 06/07/2008 - Replaced power supply |
| - | * 10/04/2017 Inspection by Tom | + | |
| - | * 11/21/2017 Inspection by Marcin | + | * 10/ |
| + | * 11/ | ||
| + | * 12/02/2017 - Made available for general use | ||
| + | * 08/08/2018 - Replaced x-axis stepper motor Lin Engineering 4109V-51 3.6V 1.2A | ||
| ===== Notes ===== | ===== Notes ===== | ||
| * Do not bump the machine while it is running, the magnetic safeties are sensitive and will kill the laser if it thinks the lid is open. | * Do not bump the machine while it is running, the magnetic safeties are sensitive and will kill the laser if it thinks the lid is open. | ||
| Line 40: | Line 55: | ||
| * A full tutorial is in progress: [[spacedocumentation: | * A full tutorial is in progress: [[spacedocumentation: | ||
| * A rough tutorial on [[spacedocumentation: | * A rough tutorial on [[spacedocumentation: | ||
| + | |||
| + | {{: | ||
equipment/lasercutterx30.txt · Last modified: 2023/09/13 03:30 by branth
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
