Milwaukee Makerspace Wiki

User Tools

Site Tools

You are here: start » spacedocumentation » lasercutterlenscleaninghowto
spacedocumentation:lasercutterlenscleaninghowto

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
spacedocumentation:lasercutterlenscleaninghowto [2014/01/15 03:10]
raster [Introduction] fixed poorly formatted dates to appease myself 		spacedocumentation:lasercutterlenscleaninghowto [2017/06/12 18:22]
tony3 More tips for cleaning the lens
Line 34: Line 34:
 {{:spacedocumentation:lensc003.jpg?direct&400|}} {{:spacedocumentation:lensc003.jpg?direct&400|}}
  
-The two bottom screws shown in the first photo above attach to the lens mount.  If the cover does not come off easily, you can remove these with a small Phillips head screwdriver and then remove the cover.+The two bottom screws shown in the first photo above attach to the lens mount.  If the cover does not come off easily, try gently moving it from side to side a tiny amount.  It is a tight fit and sometimes needs a gentle coaxing.  If there is a problem removing it, there might be something wrong.  Please find an area champion and let them know. The lens mount can be removed with a small Phillips head screwdriver in order to remove a misaligned cover, but this should be done under the supervision of an area champion.
  
 {{:spacedocumentation:60watt-first2.png?400|}} {{:spacedocumentation:60watt-first2.png?400|}}
  
-You can now try to slide the lens mount out by gently pulling it towards you with your fingers. If it doesn't move easily, try the following:+You can now try to slide the lens mount out by gently pulling it towards you with your fingers. If it doesn't move easily, an area champion can try the following:
  
 Take the small Philips head screwdriver you may have used earlier and use it to gently pry the front edge of the lens mount until it's out far enough for your to get a good grip and slide it out with your fingers. Pull it all the way out and set it down on a clean surface such as the inside cover or a piece of paper. Take the small Philips head screwdriver you may have used earlier and use it to gently pry the front edge of the lens mount until it's out far enough for your to get a good grip and slide it out with your fingers. Pull it all the way out and set it down on a clean surface such as the inside cover or a piece of paper.
Line 51: Line 51:
 {{:spacedocumentation:60watt-first4.png?400|}} {{:spacedocumentation:60watt-first4.png?400|}}
  
-Note the lens has that discolored spot on it... well, that's a damaged lens, and it **should not** look like that, which is the reason we need to be careful with the laser, always use the air assist and venting system, and clean the lens.+Note the lens has that discolored spot on it... well, that's a damaged lens, and it **should not** look like that, which is the reason we need to be careful with the laser, always use the air assist and venting system, and clean the lens after long jobs.
  
 {{:spacedocumentation:60watt-first5.png?500|}} {{:spacedocumentation:60watt-first5.png?500|}}
  
-Grab the small bottle of cleaning fluid, and a Q-tip, and add **__one drop of cleaning fluid__** onto one end of the Q-tip. (Very little fluid is needed, please use it sparingly!)  Wipe the lens clean on each side using a gentle circular motion, and then wipe the lens dry with the other side of the Q-tip, again on each side. Be sure not to leave any streaks or hairs from the Q-tip on the lens.  Let it completely dry, and then reassemble everything in reverse order of the disassemble process.+Grab the spray bottle of cleaning fluid, and a Q-tip, and add **__one drop of cleaning fluid__** onto one end of the Q-tip. (Very little fluid is needed, please use it sparingly!)  Wipe the lens clean on each side using a gentle circular motion being careful not to touch the lens holder or any other surface with dirt on it. Wipe the lens dry with the other side of the Q-tip, again on each side being careful not to touch anything dirty or you will leave streaks of dirt on the lens. Be sure not to leave any streaks or hairs from the Q-tip on the lens.  Let it completely dry, and then reassemble everything in reverse order of the disassemble process.
 ==== Second mirror ==== ==== Second mirror ====
  
Line 64: Line 64:
 {{:spacedocumentation:60watt-second2.png?500|}} {{:spacedocumentation:60watt-second2.png?500|}}
  
-Once removed, swab the mirror in a gentle circular motion with the wet end of the Q-tip then dry with the dry end.  Check that you do not leave any streaks or hairs on the mirror.  +Once removed, swab the mirror in a gentle circular motion with the wet end of the Q-tip then dry with the dry end.  Do not touch the outer portion of the mirror or the mount with the Q-tip.  If you are leaving streaks, start over with a new Q-tip. Check that you do not leave any streaks or hairs on the mirror.  
  
 {{:spacedocumentation:60watt-second3.png?500|}} {{:spacedocumentation:60watt-second3.png?500|}}
Line 76: Line 76:
 {{:spacedocumentation:60watt-thirdmirror1.png?500|}} {{:spacedocumentation:60watt-thirdmirror1.png?500|}}
  
-Insert a Q-tip into the hole at the back left corner of the machine and swab in a gentle circular motion.  +Insert a Q-tip into the hole at the back left corner of the machine and swab in a gentle circular motion being careful not to touch the sides of the holder or any other dirty surface.  
  
 {{:spacedocumentation:60watt-thirdmirror2.png?500|}} {{:spacedocumentation:60watt-thirdmirror2.png?500|}}
spacedocumentation/lasercutterlenscleaninghowto.txt · Last modified: 2017/06/12 18:22 by tony3

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki