User Tools

Site Tools


equipment:makerbotreplicator

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
equipment:makerbotreplicator [2014/04/11 17:53]
bipolarbear [Current Status]
equipment:makerbotreplicator [2017/06/22 01:16] (current)
mmelk [Current Status]
Line 21: Line 21:
   * [[http://replicat.org/download|ReplicatorG]]. Alternative to MakerWare.   * [[http://replicat.org/download|ReplicatorG]]. Alternative to MakerWare.
   * [[http://www.sketchup.com|SketchUp]].  Used to create 3D images.   * [[http://www.sketchup.com|SketchUp]].  Used to create 3D images.
 +
 =====Current Status ===== =====Current Status =====
-  * Works fine! +  * December 2015: Not working The controller board died for the second time and it has been sitting, waiting for someone to replace the controller board with Arduino/RAMPS. Note that while is it not currently functioning, it should still remain in the 3D Printing Area. 
-    - The Right extruder is out of commission until further notice. The Stepper driver appears to have gone bad but the left one is still working fine. The nozzle has been removed because it was dragging on prints and since it did not matter since it does not work. The stepper has been unplugged so that the board recognizes that it is out of commission and will not allow the nozzle to be heatedMake sure you set up your prints to use the left extruder. +  * June 2017: Nonfunctional. There are no plans to revive this printerIt has become a donor machine and educational tool for instruction on the fatal flaws of cheaply built 3D printers. Do not remove from 3D printing lab.
 ===== 3D Printing Area Champion ====== ===== 3D Printing Area Champion ======
-  * [[members:josephbozarth|Joseph Bozarth]] +  * [[members:markrehorst|the_digital_dentist]] 
 +  * [[members:jimkelly|Jim Kelly]]
 ===== Approved Trainers ===== ===== Approved Trainers =====
 (These are the people who must check out a member so they can use the 3D printer.) (These are the people who must check out a member so they can use the 3D printer.)
  
 +  * [[members:markrehorst|the_digital_dentist]]
   * [[members:josephbozarth|Joseph Bozarth]]   * [[members:josephbozarth|Joseph Bozarth]]
   * [[members:jasongessner|jason g.]]   * [[members:jasongessner|jason g.]]
   * [[members:davidb|David Buggs]]   * [[members:davidb|David Buggs]]
   * Skittles (Lucy Sinogeikina)   * Skittles (Lucy Sinogeikina)
 +  * [[members:jimkelly|Jim Kelly]]
 =====Checked Out Members ===== =====Checked Out Members =====
   * [[members:jasongessner|jason g.]]   * [[members:jasongessner|jason g.]]
Line 54: Line 56:
   * Wade Starck   * Wade Starck
   * Steve P.   * Steve P.
 +  * Emily Mondloch
 +  * Mykal Antczak
 +  * Kaysy
 +  * Steve Shapiro
 +  * Sean Woodman
 +  * Matt Schedler
 +  * Luke Schedler
 +  * Bret Daniel
 +  * Mark Rehorst
 +  * [[members:jimkelly|Jim Kelly]]
 +  * [[members:clawson|Chad Lawson]]
 =====On loan from ===== =====On loan from =====
   * [[members:jasongessner|jason g.]] (and others)   * [[members:jasongessner|jason g.]] (and others)
equipment/makerbotreplicator.1397238810.txt.gz · Last modified: 2014/04/11 17:53 by bipolarbear