Milwaukee Makerspace Wiki

User Tools

Site Tools

You are here: start » equipment » cubeprotrio
equipment:cubeprotrio

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
equipment:cubeprotrio [2014/08/12 01:53]
raster 		equipment:cubeprotrio [2017/02/06 20:54] (current)
tony3
Line 4: Line 4:
  
   * [[http://cubify.com/en/CubePro|CubePro Trio 3D Printer]]   * [[http://cubify.com/en/CubePro|CubePro Trio 3D Printer]]
 +  * Now a Maker Pro Printer - Cube guts have been removed
  
 {{ :equipment:cubeprotrio.jpg?nolink&300|}} {{ :equipment:cubeprotrio.jpg?nolink&300|}}
Line 10: Line 11:
 ===== Documentation ===== ===== Documentation =====
  
-  * +  * [[http://www.pronterface.com/|Pronterface printer control interface]] 
 +  * [[http://smoothieware.org/smoothieboard-v1|Smoothieboard hardware controller]] 
 +  * [[http://smoothieware.org/|Smoothieware software]] 
 +  * (old) [[http://cubify.s3.amazonaws.com/public/cubepro/cubepro_setup_and_repack_guide.pdf|Set-up Guide (PDF)]] 
 +  * (old) [[http://cubify.s3.amazonaws.com/public/cubepro/cubepro_user_guide.pdf|User Guide]] 
 +  * (old) [[http://cubify.com/en/CubePro/TechSpecs|Technical Specs]]
  
  
Line 16: Line 22:
  
   * Print Envelope: 285.4mm x 270.4mm x 230mm (11.2" x 10.6" x 9.06")   * Print Envelope: 285.4mm x 270.4mm x 230mm (11.2" x 10.6" x 9.06")
 +  * 1.75mm filament
 +  * Slic3r and Pronterface profile is on the computer to the left of the printer
  
  
 ===== Software ===== ===== Software =====
  
-  * ???? +  * [[http://www.pronterface.com/|Pronterface printer control interface]] 
 +  * [[http://smoothieware.org/|Smoothieware software]]
  
  
Line 27: Line 35:
  
   * 2014-08-11 - Operational!   * 2014-08-11 - Operational!
 +  * 2014-??-?? - Some extruders clogged
 +  * 2015-??-?? - All extruders clogged
 +  * 2016-09-?? - Extruders un-clogged and repaired so they don't clog whenever PLA is used
 +  * 2016-09-?? - Smoothieboard installed and operational
  
 ===== Location ===== ===== Location =====
Line 34: Line 46:
 ===== Approved Trainers ===== ===== Approved Trainers =====
  
-   * Matt N.+   * Matt M 
 +   * Marc R
  
 ===== Checked Out Members ===== ===== Checked Out Members =====
Line 44: Line 57:
   * 2014-08-07 - 3D Systems sent us a CubePro Trio\\   * 2014-08-07 - 3D Systems sent us a CubePro Trio\\
   * 2014-08-11 - Arrived at Makerspace\\   * 2014-08-11 - Arrived at Makerspace\\
 +  * 2016-09-?? - Usable software and hardware setup
  
  
 ===== Notes ===== ===== Notes =====
  
-  * Prints in 3 colors with proprietary filament cartridges+  * No longer requires proprietary software or cartridges
  
  
equipment/cubeprotrio.1407808381.txt.gz · Last modified: 2014/08/12 01:53 by raster

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki